20 Truths About Subaru Car Keys Replacement: Busted

Replacing a Subaru Car Key With an Unresponsive Button

If you have a Subaru car key that has an unresponsive button, it may be time to replace the battery. The service department at Capitol Subaru can help you with this simple process.

Open the key fob case and locate the transmitter circuit board. Find two sets of 8 digits and write the first set on a piece of paper.

Keyless entry

A keyless entry system lets you to open the doors and trunk of your Subaru without using the traditional mechanical keys. The car's computer detects presence of the key fob via the radio signal and sends an indication to unlock the doors or opening the trunk. You can also start or turn off the engine using this system. Certain advanced systems also offer remote starting, smartphone connectivity and alarms.

A reputable locksmith will be able to create a replacement Subaru key fob in case you have lost yours. They can make high-security keys that are difficult to duplicate or laser-cut keys that have more intricate designs and require special equipment to make. They can assist you in selecting the correct key for your car, and then install it for you.

To program a new Subaru key fob, first find out the type of key you own. Unlock the fob's case and check the circuit board of the transmitter. There is likely to be one or two sets of numbers with 8 digits on it. Close the fob case and note down the number. The chime will be heard on the instrument panel, and you'll notice that the dome lights flash.

subaru legacy replacement key cost G28CarKeys

If you own a Subaru that includes keyless entry, you must know how you can change the battery in the key fob. You can use a screwdriver with a flat head to open the case of your key fob and take out the battery that was in there. Then, replace it with a brand new one. Place the new battery the correct side of it inside the case.

If it's powered up by a transponder key (a combination of the words transmitter & responder) contains a microchip which communicates with the ECU of your vehicle. The chip has a digital serial number that is unique to your car. It also has a security feature that stops key duplicates.

A locksmith can program your transponder keys, but you should go to an automotive locksmith who has the right equipment and knowledge. Incorrectly programming your key could cause damage to the transponder chip inside your car keys which can cost you thousands of dollars in repairs. To program a car key, you need to first open and shut the driver's side door and then switch off and turn on your ignition. Repeat the procedure 10 times. You'll hear a sound on the instrument panel after ten repetitions.

Side-cut key

The majority of automobiles come with side-cut keys or laser-cut keys. These are a more secure version of the traditional car keys. The edges of the key are designed to match the profile of the lock's tumblers. This kind of key is difficult to duplicate and requires a specific key duplicating machine the job.

To program a Subaru Key Fob, locate the transmitter circuitry inside your key fob. (Instructions are usually in your owner's guide). Then, search for one or two sets of numbers (8-digits) on the board. Take note of these numbers to keep them in your pocket. Then, get in the driver's chair and close your door. Then, insert your new key in the ignition and move it to the initial position. After 10 seconds, the car will begin to unlock.

You can easily replace the battery on your Subaru key fob after you have a new fob. Find a small gap in the space between the front and back of the fob's encasement. Use a small screwdriver to break this enclosure open, and then take out the smaller unit from inside. Replace the old battery by the new CR2025, making sure that it's properly inserted.

Last-cut key

These keys are more convenient than traditional keys as they are able to open the doors to your car at a distance of many yards. They also allow you to start the engine. The newer models of keys are equipped with a carbon chip in them that emits an electronic signal. This adds a layer of security to your Subaru key, making it more difficult for thieves to steal.

Some drivers prefer to have an old-fashioned key for backup. If the key fob you have is not working you could try replacing the battery. If it doesn't work, you should visit Hanson Subaru or another trusted locksmith for assistance.

If your Subaru is an older model that has a laser-cut key. This key is similar to Honda's high-security keys HO01 and HO03. The type of key is equipped with four tracks, and is cut externally. It can be duplicated with typical tools that are available at locksmiths and hardware stores, but it is not equipped with onboard programming. This type of key is offered at most dealerships. However it will cost more than a cut-off one.

Key code

Subaru key fobs come with a security microchip that can be used to unlock or lock your vehicle. When you insert the key into the ignition, it transmits a signal to a receiver on your dashboard. The key's unique signal needs to be acknowledged by the dashboard's receiver in order to start the engine. If your key fob doesn't work it could be time to replace the battery.

To program the Subaru car key, first locate the eight-digit code for your vehicle. The code is on the original ringtag or on Subarunet. Once you have the code, you can open and close your driver's door, and then press the lock button several times equal to the digits in the code.

Then you need to insert the new key into the ignition and change it to the "on" position, but don't start the engine. The security light should stop blinking when the key fob starts to work. If not, replace the battery or consult a professional locksmith to troubleshoot the problem.